SMARTBox BLE

Overview

>> get the Agent
>> PSsystec Downloads

Smartbox, based on the Telit Chipset xE910 is a ready to use solution for connecting BLE Devices to the Cumulocity/Cloud of Things IoT Cloud. The SMARTbox acts as a client collecting data from up to 8 BLE devices. Easy connect and configure the used BLE devices in the cloud by Cloud fieldbus. Using the MQTT protocol the terminal comes up with a low traffic solution.

Overview

Datasheet

Radio

Radio
4G LTE
  • LTE Cat 4 (incl. 3G/2G)
  • LTE Cat 1 (incl. 3G/2G)
  • LTE Cat M1
  • NB-IoT (Cat NB1)
  • 3G
  • UMTS | HSPA+ (incl. 2G)
  • UMTS | HSPA (incl. 2G)
  • 2G GSM | GPRS
    Regions EMEA / APAC / Latinamerica / NorthAmerica / Australia / Global (3G / 2G)
    GPS Supported by 2G and 3G Variances
    Production The selected Region,Technology and GPS can be defined during Production. The default assembly is 3G with supported regions EMEA / APAC

    Connectivity/ Features

    Connectivity/ Features
    Layout Layout
    BLE Qualification v5.0 (Bluetooth low energy)
    Type GATT Client
    Connectivity 1-8 Nordic Thingy52 BLE sensors
    (Automatic Custom service identification of generic BLE sensors – not released yet)
    Chip NINA-B111-02B (ublox)
    Fieldbus Modbus
    Type Modbus RTU Master
    Baudrate 4800, 9600, 19200, 38400, 57600, 115200
    Parity Even, ODD, NONE
    Stoppbits 2,1
    Functioncodes
  • Funct.1 (Read Single Coils)
  • Funct.2 (Read Input Status)
  • Funct.3 (Read Holding Registers)
  • Funct.4 (Read Input Registers)
  • Funct.5 (Write Coil)
  • Funct.6 (Write Holding Register)
  • Datapoints Max. 10 Modbus Slaves, with 100 datapoints per device or 1000 datapoints with 1 device
    Sensors Number 12
    U1/U2/U3/U4/U5/U6/U7 DIN NO [High Side]
    24VDC
    U8 0..20mA
    U9/U10 DO – Digital Output 24VDC
    Output 24VDC Digital Output. Note: Either the Output or the 2nd Fieldbusinterface can be selected during production
    DIN/O DIN [voltage free] (defined by Hardwarejumper)
    AIN/O NTC (selectable by Hardwarejumper, either NTC or 0..20mA)
    AIN/P+ 0…20mA (selectable by Hardwarejumper, either NTC or 0..20mA)
    LEDs GSM Flashing- connected to mobile network
    RUN 2xflashing/pause: StartUp Phase
    3xflashing/pause: Connected to Server, Data exchange
    Act Flashing: Sensor Board Power
    Link Flashing: Sensor Board is ready to process data
    USB For programming, Logging and Trace the device

    Cloud Connector

    Cloud Connector
    Availability All Cumulocity Based systems, Cloud der Dinge, Deutsche Telekom
    Realtime Clock Updating Realtime automatical from #NTP timeserver
    Application CloudFieldbus (CFB Integrated in Devicemanagement)
    For SetUp connected field devices
    Online Operations Remote Restart
    Fieldbus Configuration Cloud-Device
    Change Transmitinterval from device to Cloud
    Change Communication. Baudrate, Databits, Parity, Stopbits
    Operate the connected Field device: Registervalues (R/W)
    Operate the connected Field device: Change CoilValues (R/W)
    Operate the device with AT Commands in the shell
    Communication MQTT
    Security TLS
    Notifications Realtime and Pending Operations
    Shell Operate the device with AT Commands in the shell
    Location Identification by cellular network or GPS Signal (selected- see Radio)
    Tracking Location Route by cellular network or GPS Signal
    Info Operator, Cell ID, LAC, MNC, MCC, Signal strength
    Device Database Device database Support for Modbus and Profibus: Measurements, Event, Alarms, Values, Read, Read/Write, Signed/Unsigned, Decimal Places, Multiplier, Divisor, No of Bits, StartBit
    OTA RemoteUpdate Software
    Data-Exchange Values On Change
    Alarms On Change
    Events On Change
    Measurements Default 900
    Signal strength Is sent every 20 Min as a measurement
    Offline Buffering Alarms, Events, Measurements ≈ 72h
    SMS For Troubleshooting you can operate the device by SMS:
    Reboot
    Change tenant
    FOTA/OTA

    General

    General
    Dimensions 100 x 70 x 45 mm
    Weight 89g
    GSM Antenna SMA Connector
    Power Supply Nominal voltage range: 12-24 VDC, 10%
    Maximum continuous (average) supply power: 2.5 W
    Maximum continuous (average) supply current: 200 mA at 12V, 100 mA at 24V
    Mounting Via DIN Rail Adapter or Adapter for Wall Mounting
    SIM Card Format 2FF
    Operating temperature -20..60°C
    Storage temperature -40..85°C
    Operating humidity Max. 85%
    Storage humidity Max. 85%
    IP Class IP20/IP54 (opt.)
    Approvals
    Conformity Declerations 2014/53/EU (Radio Equipment Directive - RED)

    Radio
    EN301511 v12.5.1 for GSM 900 and 1800 MHz
    EN301908 v11.1.1 for UMTS band 1 and 8
    EN300328 v2.1.1 for Bluetooth Low EnergyRoHS-DIrective 2011/65/EU

    EMC
    EN 301489-1 v2.1.1 general part
    EN 301489-52 v0.0.7 for GSM and UMTS
    EN 301489-17 v3.1.1 for for Bluetooth Low Energy

    Safety
    EN60950-01